Mar 28, 2024
Fluid evolution and related fluid
Scientific Reports volume 13, Article number: 14067 (2023) Cite this article 75 Accesses Metrics details Pore fluids control the diagenetic processes and storage spaces of deep clastic rock reservoirs
Scientific Reports volume 13, Article number: 14067 (2023) Cite this article
75 Accesses
Metrics details
Pore fluids control the diagenetic processes and storage spaces of deep clastic rock reservoirs and have become a major area of interest within the fields of sedimentology and petroleum geology. This paper aims to relate the diagenetic processes of the Oligocene Zhuhai sandstones in the Baiyun Sag to pore fluids varying with burial depth. The types and distribution patterns of authigenic minerals are investigated through analysis of petrographic, mineralogical, and geochemical features to illustrate the origin and flow patterns of pore fluids and their influences on reservoir diagenesis. Strong cementation of eogenetic carbonate cement near the sandstone–mudstone interface was a consequence of material migration from adjacent mudstones on a large scale. The pore fluids were mainly affected by microbial methanogenesis and carbonate mineral dissolution in adjacent mudstones during eogenesis. The pore fluids were diffusively transported in a relatively open geochemical system within a local range. Support for this model is provided by the heavier stable isotopic values present in eogenetic calcite and dolomite. Feldspar dissolution during early mesogenesis was spatially accompanied by the precipitation of authigenic quartz and ferroan carbonate cement. Pore fluids in this period were rich in organic acids and CO2, and their migration mechanism was diffusive transport. The obviously lighter carbon and oxygen isotopic compositions of the ferroan calcite support this inference. During late mesogenesis, the input of deep hydrothermal fluid might have been partly responsible for the precipitation of ankerite, barite and authigenic albite. Oil charging may have inhibited carbonate cementation and compaction, accordingly preserving porosity, and together with authigenic kaolinite, might have promoted the transition of the reservoir from water wet to oil wet to the benefit of oil entrapment. The findings reported here shed new light on the evaluation and prediction of sandstone reservoirs that have experienced multiple periods of fluid flow.
Pore fluids are nearly ubiquitous in clastic rocks and, with increasing burial depth, exert a crucial influence on the petrophysical properties through various fluid–rock interactions1,2,3. Aggressive pore fluids strongly corrode aluminium silicate minerals and carbonate minerals in deep clastic rock reservoirs, creating (or redistributing) secondary pores of a certain scale, thereby significantly (or slightly) improving reservoir porosities. The concomitant precipitation of secondary minerals, mainly in the form of pore-filling minerals, due to mass transfer by pore-fluid flow plays a negative role in reservoir permeability3,4,5,6,7. Identifying the origin and flow patterns of pore fluids is crucial for research on sandstone–shale diagenesis and storage properties8. Complex sandstone reservoirs interbedded with mudstone can be complicated by the potential for multiple stages of evolving pore fluids and corresponding fluid–rock interactions during progressive burial. To define and prioritize reservoir targets, the sources, flow patterns and spatiotemporal distribution of pore fluids must be understood.
Stable isotope ratios are commonly employed to constrain (1) the sources of pore fluids, (2) the pathways and timing of fluid events, (3) the formation temperatures of multiple-stage cements, and (4) the material sources of diagenetic byproducts9,10,11,12,13. The stable isotopic compositions of carbon and oxygen are highly stable in different fluid systems that have deep circulation characteristics. The degree of oxygen isotope fractionation between fluids and minerals is reduced with increasing formation temperature (surface to ~ 300°C14). The δ18O value preserved in cement can serve as a proxy record of cementation temperature. Thus, it is a useful indicator to infer the time of cement formation and to clarify the evolution of pore fluids when given a reasonable pore-fluid δ18O value15,16. Compared to the δ13C value in the original carbon pool, that preserved in cement is heavier by approximately 9–10 ‰ due to carbon isotope fractionation. Thus, δ13C values can be used to trace the external or internal sources of carbon12,13 and to address frequently asked questions related to fluid–rock interaction16,17,18,19,20. On the basis of these two stable isotope systems, combined with the regional evolution history, the physicochemical and flow features of fluids throughout the whole diagenetic process can be reconstructed21,22.
The Oligocene Zhuhai Formation in the Baiyun Sag, northern margin of the South China Sea, is a vital target of offshore petroleum exploration and development in China23. The interval consists of multistage, shelf-margin deltaic fine- to medium-grained siliciclastics. Pore fluids related to the interbedded mudstones are likely to have transported large amounts of ions driven by various mechanisms with increasing burial depth, which may have exerted a critical influence on the diagenetic processes of the sandstones24,25,26. Therefore, the Zhuhai Formation is an ideal archive for research on the characteristics of fluid evolution and related fluid–rock interactions. In this study, we investigated the type, nature and distribution patterns of diagenetic minerals in the Zhuhai sandstone reservoirs in the Baiyun Sag and clarified the evolution of the pore fluids responsible for those diagenetic processes.
The Baiyun Sag is located on the northern margin of the South China Sea and covers an area of 1.2 × 104 km2 with water depths of 200 m to 2000 m (Fig. 1a). As a Cenozoic extensional basin, the sag can be divided into a synrift stage between the Eocene and early Oligocene (65–32 Ma) and a postrift stage between the late Oligocene and the present (32–0 Ma) (Fig. 2)27. The study area, as one of the most hydrocarbon-rich deep-water areas, lies in the southeastern Baiyun Sag (Fig. 1b).
(a) Tectonic unit divisions of the Pearl River Mouth Basin, South China Sea. (b) Structural map and well locations of the Baiyun Sag (modified from 26 by using CorelDRAW Graphics Suite 2018 v20.0.0.633 https://www.corel.com/cn).
Schematic Cenozoic stratigraphy of the Baiyun Sag with tectonic evolution stages and the major reservoir formation elements (modified from 26 by using CorelDRAW Graphics Suite 2018 v20.0.0.633 https://www.corel.com/cn).
The sag is filled with Cenozoic sediments and, in ascending order, consists of the Palaeogene Shenhu, Wenchang, Enping and Zhuhai Formations; the Neogene Zhujiang, Hanjiang, and Yuehai Formations; and Quaternary groups (Fig. 2). The evolution of the synrift stage was mainly affected by the Zhuqiong movement and the Nanhai movement and can be subdivided into three stages. The studied section, i.e., the Oligocene Zhuhai Formation, was deposited in the late synrift stage and is mainly composed of Palaeo-Pearl River shelf-margin deltaic sandstones23.
The tectonic activity was relatively quiescent during the Zhuhai depositional stage. Shelf breaks stably developed in the southern deep-water area of the sag. Fluctuations in sea level and salinity were frequent and rapid. The Baiyun Sag was characterized by a wide distribution of oscillatory continental–marine transition sedimentary environments. Large-scale grey‒greyish white sandstones interbedded with brown–dark grey mudstones developed in the sag, forming a laterally extensive Palaeo-Pearl River shelf-margin delta system. The sedimentary facies were dominated by subaqueous distributary channels, mouth bars and sheet sands in the southern deep-water area of the sag and inter fingered with more subaqueous inter distributary bay and pro delta argillaceous deposits. The thick, organic-rich mudstones are important potential hydrocarbon source rocks for the intercalated thin sandstone reservoirs27.
Sixty-five core samples with burial depths of 800–3000 m were collected from five wells (Fig. 1). All samples were obtained from delta deposits with various thicknesses. To analyse the underlying correlation between reservoir quality and distance from the sandstone–mudstone interface, samples were selected from different positions within one bed. A total of 210 core analysis data points of Zhuhai sandstones were taken to evaluate porosity and permeability.
Point counting was performed on 116 thin sections of Zhuhai sandstone in the southeastern Baiyun Sag in this study to estimate the modal composition. Thin sections were impregnated with blue epoxy under vacuum to identify visual porosity and stained with potassium ferricyanide and Alizarin Red S to aid in distinguishing carbonate. A total of 300 points were counted for each thin Sect.28. For the accurate estimation of cement and pore contents, 20 micrographs per thin section were first obtained under a Zeiss microscope, and the targets per micrograph were then sketched and calculated using the AxioVision software Rel and Image-Pro Plus software. Finally, the average values of each target area in all micrographs were obtained, which can be regarded as the contents of pores and cement.
All 65 samples were prepared for mineralogical X-ray diffraction (XRD) analysis using an Ultima IV X-ray diffractometer. Samples were X-rayed, centrifuged, glycolated, and heated to 550 °C. XRD analysis was based on the procedure used by29 within an error range of 10%. After detailed petrographic analysis, seven representative samples were observed using cathodoluminescence microscopy (CL) to distinguish multiphase carbonate cement. For the spatial morphology of authigenic mineral identification, 22 gold-coated samples were observed under a ZEISS EVO LS15 scanning electron microscope (SEM) equipped with an energy-dispersive spectroscopy X-ray microanalyzer.
Thirty organic matter-free sandstone samples were prepared based on petrological studies for carbon and oxygen isotope measurements. To target specific carbonate cement generations, microsamples (0.35–0.45 mg) of different types of cement were drilled from thick petrographic sections using a microscope-mounted dental drill. Each sample was reacted with 100% ortho-phosphoric acid at 70 °C for 4 to 8 h. The carbon and oxygen stable isotope values were obtained from the CO2 liberated from the carbonate cement samples using a Thermo-Finnigan MAT 253 IRMS. The measurement precision was ± 0.014‰ for oxygen and ± 0.02‰ for carbon. The stable isotope data were reported in δ notation relative to the Pee Dee belemnite (V-PDB). δ18OVPDB values were converted to δ18OVSMOW (Vienna standard mean ocean water) values using the equation δ18OVSMOW = 1.03091 × δ18OVPDB + 30.9130.
Seven core samples were prepared as doubly polished fluid inclusion wafers for microthermometric measurement. Microthermometry was conducted using a calibrated LINKAM THMSG600 stage. The homogenization temperature (Th) was obtained by cycling. Th values were measured using a heating rate of 10 °C/min when the temperature was lower than 80 °C and a rate of 5 °C/min when the temperature exceeded 80 °C. The measured temperature precision for Th was ± 1 °C. All the analyses mentioned above were performed in the Key Laboratory of Petroleum Resources Research, CAS (Lanzhou).
Compositionally, the studied Zhuhai sandstones are dominantly feldspathic litharenites followed by lithic arkoses (Fig. 3). They are mostly fine- to medium-grained, moderately to well sorted and subangular to subrounded. Based on point-count data, detrital quartz accounts for 34–85% (average 56.5%) and is the predominant framework grain. Detrital feldspar accounts for 3–38.5% (average 20.3%), and K-feldspar (average 14.9%) is more abundant than plagioclase (average 5.4%). The rock fragment content is approximately 4–38.2% (average 23.2%) and consists of 2.5–28% volcanic rocks (average 13.8%), 0.3–26.5% sedimentary rocks (average 2.78%), and 0.3–14.7% metamorphic rocks (average 6.62%). Only small quantities of micas and heavy minerals can be found. The mud content is 0.3–45% (average 4.68%), and the cement content is 0.2–32.3% (average 7.24%). The compositional maturity varies between 0.52 and 5.67, with an average of 1.55.
Triangular diagram of the rock composition of the Zhuhai sandstones in the Baiyun Sag. All data come from optical point counting of thin sections.
Partial to complete feldspar grain dissolution is very common in the Zhuhai sandstones, and most dissolved grains are K-feldspar and locally plagioclase. Feldspar grains preferentially dissolved along the cleavage, revealed as irregular dissolution edges and feldspar residue (Fig. 4a,b,d). Some feldspar grains were almost totally dissolved, forming mouldic pores (Fig. 4c). Spatially, feldspar-dissolution pores are accompanied by pore-filling authigenic clays, albite and quartz cements (Fig. 4c and e). The authigenic albite presents as columnar aggregates of euhedral crystals, and the elongated crystals are parallel to the cleavage of the dissolved K-feldspar (Fig. 4f). The content of dissolved feldspar is 0.1–3.1%, with an average of 1.26%. The quantity of dissolution pores marginally increases with burial depth (Fig. 5a); moreover, there is a marked increase in sandstones more than 1 m away from the sandstone–mudstone contact within a bed (Fig. 6a).
Photomicrographs of feldspar dissolution and associated authigenic minerals in the Zhuhai sandstones. (a) LW1-1, 1707.5 m: dissolution of feldspar along the cleavages; (b) LW4-1, 1519.8 m: leached feldspar with the precipitation of secondary kaolinite and associated secondary minerals; (c) LW1-2, 2429.5 m: feldspar-dissolution mouldic pores and kaolinite precipitation; (d) LW1-1, 1707.5 m: SEM micrograph showing leached feldspar along the cleavages; (e) LW3-1, 1861.5 m: SEM micrograph showing a feldspar-dissolution pore filled by clay precipitation; (f) LW1-2, 2509.5 m: precipitation of albite on leached feldspar. Note: Q = quartz, FD = feldspar dissolution, PP = primary pore, IS = illite and smectite mixed layers, K = kaolinite, and Al = albite.
Vertical distribution characteristics of the main diagenetic products in the Zhuhai sandstone. Point-count data of thin sections are used.
The relationship between the abundance of the main diagenetic products in the sandstones and the distance to the sandstone–mudstone interface. Point-count data of thin sections are used.
Carbonate cements are the most abundant of the secondary minerals, and the mean content is 11.6% (range 0.2–28%) (Fig. 5d). These cements are mainly composed of calcite (Fig. 7a), dolomite (Fig. 7b), ferrocalcite (Fig. 7c), ankerite (Fig. 7d, and e) and siderite (Fig. 7f). Calcite (average 2.54%) is mainly present as poikilotopic blocky or pore-filling crystals with crystal sizes in the range of 5–300 μm, which either infilled primary pores or replaced detrital grains partially or completely. Calcite was observed to be zoned and engulfed by ferroan calcite (Fig. 7c).
Photomicrographs of carbonate cements in the Zhuhai sandstones. (a) LW1-1, 2027.25 m: poikilotopic, blocky calcite filling most primary pores; (b) LW1-1, 2037.5 m: dolomite filling intergranular primary pores with zoning and engulfed by ankerite; (c) LW1-2, 2563.5 m: calcite replaced by ferrocalcite; (d) LW1-2, 2563.5 m: quartz overgrowths replaced by ankerite; (e) LW1-1, 2037.5 m: dolomite engulfed by ankerite; (f) LW1-2, 2429.5 m: siderite precipitated around detrital grains. Note: Cc = Calcite, Do = Dolomite, Fc = Ferroan calcite, An = Ankerite, FD = Feldspar dissolution pore, Qa = Quartz overgrowth, Sid = Siderite.
Dolomite (average 1.07%) is commonly composed of microsparry or micritic aggregates (5–250 μm) that generally appear as rhombohedral crystals (Fig. 7b and e). Dolomite cements were also observed to fill primary pores between uncompacted framework grains as pore-filling poikilotopic cement.
Ferroan calcite (average 1.69%) is mainly present as isolated crystals filling pores and secondarily scattered euhedral crystals (5–200 μm; Fig. 7c), while ankerite (average 4.62%) mainly occurs as euhedral rhombs (5–150 μm; Fig. 7d) and mosaic clusters (10–250 μm; Fig. 7e). These cements partly occupy fractures and feldspar-dissolution pores and have replaced clastic grains or early carbonate cements (Fig. 7b,c,e). The siderite ranges in colour from light to dark brown and appears as irregular rhombs filling intergranular pores (Fig. 7f).
The carbonate cement content is commonly observed to be higher in sandstones less than 1.0 m away from the sandstone–mudstone interface (Fig. 6b), forming sandstones tightly cemented by calcite and dolomite filling all the intergranular pores (Fig. 7).
On the basis of the isotopic analysis, the calcite cements have δ13C values between − 0.3 and + 2.51‰, and δ18O values range between − 11.27 and − 8.28‰. The dolomite cements have a range of δ13C values (− 0.76‰ to + 2.12‰) and δ18O values (− 11.24‰ to − 8.49‰) that are similar to those of calcite. In contrast, the ferroan calcite cements have significantly lighter δ13C values (− 24.42‰ to − 4.19‰) and slightly lighter δ18O values (− 16.63‰ to − 13.67‰) (Table 1). For the ankerite cements, the δ18O values do not vary much, ranging between − 18.05 and − 12.06‰, but the δ13C values are significantly heavier (− 7.72‰ and − 1.02‰; Table 1, Fig. 8) than those of the ferroan calcite.
Crossplot of δ13C and δ18O compositions of carbonate cements in the Zhuhai sandstones. Standard isotopic zones for carbon sources of variable carbonate cements are according to 32.
Authigenic quartz can be categorized into three types according to various morphologies: syntaxial overgrowths, small prismatic euhedral crystals, and microfracture-filling quartz cements (Fig. 9). Two stages of quartz overgrowth with thicknesses varying from 2 to 60 μm could be locally identified (Fig. 9a,b,e). The first stage of quartz overgrowth (Qa1) was enclosed or engulfed by ankerite and ferroan calcite cements (Fig. 7d), indicating that ankerite and ferroan calcite cementation occurred after Qa1. The quartz cement content is relatively low and stable, making up less than 1% (Fig. 5b), and has a positive correlation with feldspar dissolution porosity (Fig. 6c).
Photomicrographs of quartz, clay and other cements in the Zhuhai sandstones. (a) LW1-1, 1714.25 m: Two phases of quartz overgrowths; (b) LW1-1, 2563.5 m: Two phases of quartz overgrowths, and the dissolution of feldspar along the cleavages; (c) LW1-2, 2509.5 m: Syntaxial quartz overgrowths; (d) LW1-1, 1714.25 m: Quartz overgrowths and prismatic quartz crystals; (e) LW1-1, 2563.5 m: Two phases of quartz overgrowths and kaolinite cover on grain surface; (f) LW4-1, 1559.8 m: Kaolinite and ankerite in sandstones; (g) LW1-2, 2509.5 m: Transition of kaolinite to illite; (h) LW1-1, 2563.5 m: Barite filling among particles; and the yellow cross represents an EDS analysis point; (i) LW1-1, 2563.5 m: EDS-tested composition of the barite (BaSO4). Note: Qa1 = first phase of quartz overgrowth, Qa2 = second phase of quartz overgrowth, K = kaolinite, I = illite.
Aqueous inclusions are primarily present in the microfracture-filling quartz cements (Fig. 10a) and partly in the quartz overgrowths (Fig. 10b), with a few in carbonate cements. These aqueous inclusions are commonly two-phase liquid–vapour inclusions with a diameter range of mainly from 3 to 9.5 μm. The Th values of aqueous fluid inclusions range from 77.5 to 125 °C in the quartz overgrowths and from 94.3 to 146 °C in the microfractures (Table 2, Fig. 11). Only two Th values of aqueous fluid inclusions were measured in ankerite, 113.7 °C and 124.3 °C (Fig. 11). According to measured Th values, two stages of quartz overgrowth were confirmed. The mean Th value of aqueous inclusions in Qa1 is 89.8 °C (range 77.5–107.9 °C), and that in Qa2 is 114.3 °C (range 104.5–125 °C) (Table 2).
Photomicrographs of aqueous inclusions in annealed microfractures in quartz grains (a) and quartz overgrowths (b) under transmitted light observed in Zhuhai sandstones of the Baiyun Sag.
Histograms of Th for aqueous inclusions in annealed microfractures, quartz overgrowths and ankerite in Zhuhai sandstone reservoirs.
The main authigenic clay mineral types are kaolinite and illite in the studied interval, followed by illite/smectite mixed layer and chlorite. Kaolinite fills primarily primary pores as well as feldspar-dissolution pores and generally occurs in the forms of vermicular pseudohexagonal and euhedral booklet aggregates (Fig. 4b and c). The kaolinite aggregates consist mainly of thin, closely associated platelets with obvious intercrystalline microporosity (Fig. 9e and f). Some kaolinite crystals feature fibrous edges due to illitization (Fig. 9g). The honeycomb-textured illite‒smectite mixed layer features schistose crystals with a rolled border approximately 5 to 10 μm in size under SEM. Fibrous and flaky illite can also be observed in primary pores and dissolved pores and locally on grain surfaces (Fig. 9g). Similar to the quartz cement, a positive relationship also exists between the abundance of clay minerals and feldspar-dissolution porosity (Fig. 6d).
Based on XRD analysis of the clay fraction (< 2 μm) of sandstones, kaolinite is the major clay mineral and is dominant at depths above 2000 m, decreasing sharply in abundance below this depth, particularly below approximately 2500 m. Illite is dominant at depths greater than 2000 m (Fig. 12). Additionally, the contents of the illite/smectite mixed layer and chlorite have wide ranges and show marked increases from 1900 to 2100 m and from 2250 to 2350 m, respectively (Fig. 12).
The content of clay minerals versus burial depth in the Zhuhai sandstones. X-ray diffraction data are used.
Barite can be identified as a minor diagenetic mineral with small amounts of less than 1%. Based on the SEM‒EDS analysis, irregularly shaped barite (BaSO4) commonly fills the gaps among clastic grains in the Zhuhai sandstones (Fig. 9h and i).
The Oligocene Zhuhai sequence experienced stable and persistent subsidence after deposition (Fig. 13). The overlying strata of the Zhuhai layer include up to 2200 m of deep-sea gravity flow and muddy sediments, and the average water depth at present is approximately 1450 m27. The Baiyun Sag is a typical hot basin, as demonstrated by previous studies, with present-day heat flow values of 24.2 to 121.0 mW/m233. The geothermal gradient has a steady rise from northwest to southeast in the sag, which can be up to approximately 55 °C/km for the study area34. This discrepancy could be due to the southward transition of the spreading ridge and crustal thinning caused by the Baiyun movement since 23.8 Ma and neotectonics since ca. 13.8 Ma, along with continual deep thermal fluid upwelling in the southeastern Baiyun Sag35.
Burial history, diagenetic sequence and porosity evolution of the Zhuhai reservoirs in well LW1-1.
The average subsidence depth of the Zhuhai Formation is approximately 3600 m. The present-day maximum burial depth is approximately 3000 m, with a maximum temperature of approximately 140 °C36. Overpressure developed at 30 Ma and gradually increased to a peak at 13.8 Ma to 10 Ma. Afterwards, the overpressure sharply decreased and reached the present normal pressure37.
A temperature of 70 °C is generally regarded as the dividing line between eogenesis and mesogenesis8. Compaction is the dominant eogenetic process. The precipitation of calcite and dolomite is common, especially in sandstones less than 1.0 m away from the sandstone–mudstone interface (Fig. 6b). Siderite is also demonstrated to be an eogenetic product in view of the filling relationships of these cements and primary pores between uncompacted framework grains (Fig. 7f).
According to the latitudinal gradient of the δ18O value of modern-day global precipitation38, the δ18OSMOW values of the sedimentary water in the Baiyun sag can be considered − 5‰ (ranging from 0 to − 10‰) for the palaeolatitude of the sag at approximately 20°N. This value represents the δ18OSMOW value of the pore fluid from which carbonate cements precipitated during eogenesis. On the basis of the fractionation equations of the oxygen isotopes for calcite–water39 and dolomite–water40, the calculated formation temperatures are between 29 and 45 °C for the calcite cements and between 59 and 80 °C for the dolomite cements (Table 2).
Further compaction and feldspar dissolution were the main mesogenetic processes in the Zhuhai sandstones. The secondary pores generated from the dissolution of feldspars are observed to be mostly filled with diagenetic byproducts, such as clay and quartz cements (Figs. 4 and 5)23,41. The point and linear contact between detrital minerals indicates that minimal pressure dissolution has occurred in the Zhuhai sandstones. Pressure dissolution may have limited significance for quartz overgrowth42. The aqueous inclusions in the quartz overgrowths have a continuous Th distribution (70 °C to 130 °C) (Table 1), indicating continuous development of these cements43. The formation temperatures are 77.5–107.9 °C and 104.5–125°C for Qa1 and Qa2, respectively. It is inferred that feldspar dissolution and clay mineral transformation acted as an internal silica source for quartz cementation.
Petrological evidence, such as ferroan carbonate cements commonly filling feldspar-dissolution pores, suggests that these cements probably postdate the feldspar dissolution. The δ18O value of pore fluid becomes heavier with increasing temperature due to isotopic modification by feldspar alternation and other fluid–rock interactions12,44. The δ18OSMOW values of the pore fluid during mesogenesis were assumed to be − 5‰, − 2‰, and 0‰44. Using a δ18OSMOW value of − 2‰ and the fractionation equations of oxygen isotopes for calcite–water39 and dolomite–water45, the precipitation temperatures are calculated to be 79–101 °C for the ferroan calcite and 91–152 °C for the ankerite (Table 2). The measured Th of aqueous fluid inclusions in the ankerite cements (113.7 °C, 124.3 °C, Table 1) are within the results calculated for the ankerite. Therefore, it is reasonable to assume that the pore fluid had a δ18OSMOW value of − 2‰ when the ferroan carbonate cements precipitated during mesogenesis.
Hydrocarbon inclusions are pervasively developed and are closely associated with the coeval aqueous inclusions in quartz microfractures in the Zhuhai sandstones (Fig. 10a). The Th of the coeval aqueous inclusion is regarded as the closest equivalent to the trapping temperature of the coexisting hydrocarbon inclusions, and it ranges from 94.3 to 146 °C, as previously stated. This result agrees with the previous detailed work of46, which showed that two periods of oil charge exist in the study area, occurring at 13.1–7.3 Ma and 5.5–0 Ma46. The first period of oil charge postdated the dissolution of feldspar and antedated or was synchronous with the precipitation of mesogenetic ferroan calcite. The second period of oil charge postdated the late ankerite cementation (Fig. 13).
Figure 13 illustrates the paragenetic sequence of the main diagenetic events of the Zhuhai sandstones. However, not all reservoirs experienced the entire paragenetic sequence mentioned above47. Parts of reservoirs, especially thin beds or the marginal parts of thick beds (< 1.0 m), were rich in early calcite and dolomite cements during eogenesis, even filling all the intergranular spaces and becoming tight reservoirs, and hardly any other diagenetic alteration occurred (Figs. 13a and 14a). The middle parts of thick beds (> 1.0 m), by contrast, experienced complex diagenetic histories, mainly including compaction, weak early carbonate cementation, and relatively strong dissolution of feldspar (Fig. 14b,c). Subsequently, reservoirs without the early oil charge experienced strong cementation of the late carbonate, whereas the charging of late oil slowed late carbonate cementation to a certain extent (Fig. 13(b) and 14(b)). For reservoirs with the early oil charge, the selective early oil charge affected the path of diagenetic evolution; in particular, it significantly hindered late carbonate cementation. This resulted in the alteration of the wettability from water wet to oil wet. This aided the second period of oil charge (Figs. 13b and 14b).
Schematic diagram showing the fluid flow and diagenetic evolution of the Zhuhai sandstones.
The eogenetic products record early burial fluids during the precipitation process and the climatic conditions during deposition8,23. The rapid subsidence of the studied interval suggests that the pore fluids during eogenesis were not significantly influenced by meteoric water. In addition, meteoric water has a δ13C value of − 7‰, which is much lower than the δ13C values of the early-formed calcite cements (− 0.76‰ to + 2.51‰), indicating that it contributed little to the precipitation of these cements.
The greater precipitation of calcite and dolomite in sandstones less than 1.0 m away from the sandstone–mudstone interface (Fig. 6b) indicates that interbedded mudstones might have been a crucial source of the early-formed carbonate cements in the sandstones. The interbedded shelf mudstones contain a considerable amount of organic matter (TOC values range from 0.66 to 1.47%, average 1.08%)48. The bicarbonate species related to microbial methanogenesis of organic matter (δ13C up to + 8‰) might have been an important carbon source for the early-formed calcite and dolomite. This is supported by the relatively positive δ13C values (− 0.76‰ to + 2.51‰) of these cements (Fig. 14a)49. In addition, the mudstones in the Zhuhai Formation are high in detrital carbonate minerals (over 15%)50. These minerals have δ13C values that vary from 0 to + 5.9‰51. The dissolution of the carbonate minerals in adjacent mudstones could thus be another carbon source52. Additionally, the Ca2+ and Mg2+ ions dissolved in the mudstone were probably transported to sandstone as well.
During this stage, pore fluids from the mudstones interbedded with the sandstones were mainly driven by compaction (Fig. 14d). Large-scale mass transfer occurred from the mudstones to adjacent sandstones, implying that a relatively open diagenetic environment occurred within a local range (e.g., several metres). The rapid subsidence and extensive mechanical compaction of the mudstones during eogenesis may have expelled fluids into adjacent sandstone reservoirs53. However, much of the research to date has demonstrated that the rate of fluid flow from mudstones to sandstones is rather low, only several millimetres per year4,54. Thus, advection and convection likely made an insignificant contribution to mass transport. With the dissolution of carbonate minerals, microbial alteration of organic matter in mudstones alters the ion concentration of pore fluids, creating steep diffusion gradients. The diffusive transport of dissolved ions from mudstones to sandstones may have had a great impact on the distribution pattern of the early carbonate cements. Similar conclusions have been reached in other sedimentary basins8,54,55.
Due to thermal maturation of kerogen (temperature > 70 °C), a chemical gradient was formed between the source rock and adjacent sandstones. Organic CO2 and acids were transported via diffusion. This resulted in a certain amount of feldspar dissolution56,57. However, the dissolution of feldspar barely occurred near the edge but rather occurred in the middle part of the sandbodies (Fig. 6). The most likely cause is strong carbonate cementation near the sandstone–mudstone interface during diagenesis, resulting in tight layers forming along the sandbody edges, which control the transport of pore fluids rich in organic CO2 and acids, crossing the sandbody edge and reaching the porous zone in the centre of the sandbody (Fig. 14b).
The solubility of silica is extremely low42,54. Together with the relatively limited flux of formation water, which is difficult over long distances and in large quantities, the distribution patterns of quartz cement indicate little or no external silica involvement (Fig. 6)54. The intimate association between diagenetic mineral assemblages (Fig. 6) suggests that the silica source of quartz cement is closely related to feldspar dissolution. This is also supported by the precipitation temperature zone of Qa1 (77.5 °C to 107.9 °C, average 89.8 °C). Thus, the dissolution of feldspar may have served as an important silica source for Qa134,42,58. As mentioned before, kaolinite is mainly stable above 2000 m (temperature < 100 °C), and the rapid and mass illitization of kaolinite occurs in the sandstone below 2000 m, especially between 2200 and 2500 m (with temperatures from 100 to 120 °C). The formation temperature of Qa2 ranges from 104.5 to 125 °C, with an average of 114.3 °C, coinciding with the optimal temperature zone of the illitization of kaolinite. It seems highly likely that the illitization of kaolinite was a major source of silica for Qa2 in the study area.
The relatively negative δ13C values (− 24‰ to − 1‰) of the ferroan calcite suggest an organic source from adjacent mudstones.
(δ13CVPDB from − 25 to − 10‰) (Table 2)49. In addition, the precipitation of ferroan carbonate replacing nonferroan carbonate can be caused by abundant organic CO2 that can dissolve some early-formed carbonate. Thus, the ferroan carbonate precipitation during early mesogenesis was dominated by a mixture of carbon sources from the decarboxylation of organic matter and dissolution of early-formed carbonate cements. The illitization of smectite (60–100 °C) in the mudstones is consistent with the temperature range of the ferroan carbonate cements25, which can release Fe2+ that is transported to sandstones via diffusion, and this process may have served as the main source of the ferroan carbonate cements in the sandstone49,59,60, as evidenced by the distribution pattern of carbonate cements proximal and distal to the sandstone–mudstone interface. It is inferred that there was a relatively open system for organic CO2 and Fe 2+ ion transfer on the local scale during early mesogenesis, and the predominant dissolved material was driven by diffusive transport.
The ankerite cements have higher δ13C values than the ferroan calcite and formed at significantly higher temperatures (91–152 °C), suggesting another origin from CO2-containing deep hydrothermal fluid (Fig. 14d). The hydrothermal fluid from depth had δ13C values of approximately − 5 ± 2‰ and generally positive δ18O values ranging from + 5.0 to + 7.0‰61. The increasing δ13C and δ18O values of the ankerite with increasing temperature may be related to the ascent and intrusion of hydrothermal fluid from depth to the sandstones. This conclusion is supported by the precipitation of barite and albite, which are typical hydrothermal minerals, as noted by others28,29,62. It is likely that diffusion was predominant in a locally open system with migration of hydrothermal fluid during late mesogenesis. Further study with more focus on this hydrothermal fluid is suggested.
Oil charge may inhibit the compaction and late carbonate cementation of reservoirs, consequently acting to preserve porosity63,64. In the studied interval, the oil saturation of the reservoirs steadily increases as the content of carbonate cements decreases, which corresponds to a gradual increase in porosity (Fig. 15). There are numerous differences between the two periods of oil charge in terms of the impact on reservoir quality64. The first period of oil charging effectively inhibited the precipitation of ferroan calcite and ankerite prior to mesogenetic cementation (Fig. 14b,c). The first period of oil charge was synchronous with or subsequent to the transformation of feldspar to kaolinite. Both of the events may have altered the reservoir wettability to oil wet, which helped the subsequent oil charging and entrapment64,65,66. Overall, high-quality reservoirs might be present in the middle part of the thickly bedded delta sandstones, and these reservoirs experienced both periods of oil charging.
Binary diagram of porosity versus carbonate cement content in sandstones with different oil contents.
This paper presents the evolution of fluids with progressive burial and the complex interactions with sandstone reservoirs, as exemplified by the Oligocene Zhuhai sandstones in the Baiyun Sag. On the basis of detailed analyses of petrographic, mineralogical, and geochemical features in the Zhuhai sandstones, this study has demonstrated the following.
(1) The Oligocene Zhuhai sandstones experienced compaction and calcite and dolomite cementation in the eogenetic stage. Subsequently, they underwent two phases of feldspar dissolution and concomitant quartz overgrowth formation, the cementation of ferroan calcite and ankerite, the conversion of clay minerals, and two periods of oil charging in the mesogenetic stage. The precipitation of typical hydrothermal minerals (such as authigenic albite and barite) was synchronous with ankerite in the late mesogenetic stage.
(2) The pore fluids were influenced by microbial methanogenesis and carbonate mineral dissolution in adjacent mudstones during the eogenetic stage. Large-scale mass transfer occurred along steep diffusion gradients in a relatively open geochemical system and resulted in abundant precipitation of calcite or dolomite within 1.0 m of the sandstone–mudstone interface. This conclusion is supported by the heavier carbon and oxygen isotopic compositions during eogenesis.
(3) Thermal maturation of organic matter significantly controlled the pore fluids in the early mesogenetic stage. Organic acid and CO2 contributed to the dissolution of feldspar and early cements. Diffusion-migrated dissolved material was mainly reprecipitated in situ or in adjacent pores in the form of authigenic quartz and ferroan calcite. This conclusion is supported by the obviously lighter isotopic compositions of the early mesogenetic ferroan calcite. During late mesogenesis, dissolution might have been partly driven by deep hydrothermal fluid. Evidence that supports this interpretation includes the precipitation of typical hydrothermal minerals and the abnormally high isotopic compositions of the late ankerite.
(4) Oil charging, especially the first period of oil charging, may have inhibited carbonate cementation and compaction, accordingly causing the preservation of porosity. This could have altered the reservoir wettability from water wet to oil wet in combination with the precipitation of authigenic kaolinite caused by feldspar dissolution. The multistage pore-fluid activity and related fluid–rock interaction lead to the potential for high-quality reservoirs developed in the middle part of the thickly bedded delta sandstones that experienced both periods of oil charge.
All data generated or analysed during this study are included in this published article.
Winter, B. L., Johnson, C. M., Simo, J. A. & Valley, J. W. Paleozoic fluid history of the Michigan basin: Evidence from dolomite geochemistry in the middle Ordovician St. Peter Sandstone. J. Sediment. Res. 65, 306–320 (1995).
Google Scholar
Morad, S., Al-Ramadan, K., Ketzer, J. M. & De Ros, L. F. The impact of diagenesis on the heterogeneity of sandstone reservoirs: A review of the role of depositional facies and sequence stratigraphy. AAPG Bull. 94, 1267–1309 (2010).
Article CAS Google Scholar
Bjørlykke, K. & Jahren, J. Open or closed geochemical systems during diagenesis in sedimentary basins: Constraints on mass transfer during diagenesis and the prediction of porosity in sandstone and carbonate reservoirs. AAPG Bull. 96, 2193–2214 (2012).
Article Google Scholar
Giles, M. R. Mass transfer and problems of secondary porosity creation in deeply buried hydrocarbon reservoirs. Mar. Pet. Geol. 4(3), 188–204 (1987).
Article CAS Google Scholar
Lasaga, A. C. & Luttge, A. Variation of crystal dissolution rate based on a dissolution stepwave model. Science 291(5512), 2400–2404 (2001).
Article ADS CAS PubMed Google Scholar
Fu, Q. et al. Coupled alkali-feldspar dissolution and secondary mineral precipitation in batch systems: 1. New experiments at 200 °C and 300 bars. Chem. Geol. 258(3–4), 125–135 (2009).
Article ADS CAS Google Scholar
Yuan, G. H., Cao, Y. C., Gluyas, J. & Jia, Z. Z. Reactive transport modeling of coupled feldspar dissolution and secondary mineral precipitation and its implication for diagenetic interaction in sandstones. Geochim. Cosmochim. Acta 207, 232–255 (2017).
Article ADS CAS Google Scholar
Morad, S., Ketzer, J. M. & Deros, L. F. Spatial and temporal distribution of diagenetic alterations in siliciclastic rocks: Implications for mass transfer in sedimentary basin. Sedimentology 47, 95–120 (2000).
Article CAS Google Scholar
Morad, S., Al-Aasm, I. S., Ramseyer, K., Marfifil, R. & Aldahan, A. Diagenesis of carbonate cements in Permo-Triassic sandstones from the iberian range, Spain: Evidence from chemical composition and stable isotopes. Sediment. Geol. 67, 281–295 (1990).
Article ADS Google Scholar
Spezzaferri, S., McKenzie, J. A. & Isern, A. Linking the oxygen isotope record of late Neogene eustasy to sequence stratigraphic patterns along the Bahamas margin: Results from a paleoceanographic study of ODP Leg 166, Site 1006 sediments. Mar. Geol. 185, 95–120 (2002).
Article ADS CAS Google Scholar
Melezhik, V. A., Fallick, A. E., Smirnov, Y. P. & Yakovlev, Y. N. Fractionation of carbon and oxygen isotopes in C-13-rich Palaeoproterozoic dolostones in the transition from medium-grade to high-grade greenschist facies: A case study from the kola superdeep drillhole. J. Geol. Soc. 160, 71–82 (2003).
Article ADS CAS Google Scholar
Fayek, M. et al. In situ stable isotopic evidence for protracted and complex carbonate cementation in a petroleum reservoir, north coles levee, San Joaquin Basin, California, USA. J. Sediment. Res. 71, 444–458 (2001).
Article ADS CAS Google Scholar
Longstaffe, F. J., Calvo, R., Ayalon, A. & Donaldson, S. Stable isotope evidence for multiple flfluid regimes during carbonate cementation of the Upper Tertiary Hazeva Formation, Dead Sea Graben, southern Israel. J. Geochem. Explor. 80, 151–170 (2003).
Article CAS Google Scholar
Milliken, K. L. & Land, L. S. The origin and fate of silt sized carbonate in subsurface miocenee oligocene mudstones, south Texas Gulf Coast. Sedimentology 40, 107–124 (1993).
Article ADS CAS Google Scholar
Mansurbeg, H. et al. Meteoric-water diagenesis in late cretaceous canyon-fill turbidite reservoirs from the Espirito Santo Basin, eastern Brazil. Mar. Pet. Geol. 37, 7–26 (2012).
Article CAS Google Scholar
Liu, S. B., Huang, S. J., Shen, Z. M., Lu, Z. X. & Song, R. C. Diagenetic fluid evolution and water–rock interaction model of carbonate cements in sandstone: An example from the reservoir sandstone of the fourth member of the Xujiahe formation of the Xiaoquan-Fenggu area, Sichuan Province, China. Sci. China Earth Sci. 57, 1077–1092 (2014).
Article ADS Google Scholar
Bourque, P. A., Savard, M. M., Chi, G. X. & Dansereau, P. Diagenesis and porosity evolution of the upper silurian-lowermost devonian west point reef limestone, eastern Gaspe Belt, Quebec Appalachians. Bull. Can. Pet. Geol. 49, 299–326 (2001).
Article Google Scholar
Sanyal, P., Bhattacharya, S. K. & Prasad, M. Chemical diagenesis of Siwalik sandstone: Isotopic and mineralogical proxies from Surai Khola section, Nepal. Sediment. Geol. 180, 57–74 (2005).
Article ADS CAS Google Scholar
Xi, K. L. et al. Diagenesis and reservoir quality of the Lower Cretaceous Quantou Formation tight sandstones in the southern Songliao Basin, China. Sediment. Geol. 330, 90–107 (2015).
Article ADS Google Scholar
Yang, Z. et al. Formation mechanism of carbonate cemented zones adjacent to the top overpressured surface in the central Junggar Basin, NW China. Sci. China Earth Sci. 53, 529–540 (2010).
Article ADS CAS Google Scholar
El-Ghali, M. A. K., Mansurbeg, H., Morad, S., Al-Aasm, I. S. & Ajdanlisky, G. Distribution of diagenetic alterations in flfluvial and paralic deposits within sequence stratigraphic framework: Evidence from the Petrohan Terrigenous group and the Svidol formation, lower Triassic, NW Bulgaria. Sediment. Geol. 190, 299–321 (2006).
Article ADS CAS Google Scholar
El-Ghali, M. A. K. et al. Distribution of diagenetic alterations within depositional facies and sequence stratigraphic framework of fluvial sandstones: Evidence from the petrohan terrigenous group, lower Triassic, NW Bulgaria. Mar. Pet. Geol. 26, 1212–1227 (2009).
Article CAS Google Scholar
Mi, L. J., Liu, B. J., He, M., Pang, X. & Liu, J. Petroleum geology characteristics and exploration direction in Baiyun deep water area, northern continental margin of the South China Sea. China Offshore Oil Gas 28, 10–22 (2016) ([in Chinese with English abstract]).
Google Scholar
Mansurbeg, H. et al. Diagenesis and reservoir quality evolution of palaeocene deep-water, marine sandstones, the Shetland-Faroes Basin, British continental shelf. Mar. Pet. Geol. 25, 514–543 (2008).
Article Google Scholar
Luo, J. L. et al. Diagenetic response on thermal evolution events and high geothermal gradients in the southern Pearl River Mouth Basin and its enlightenment to hydrocarbon exploration. Acta Pet. Sin. 40, 90–104 (2019) ([in Chinese with English abstract]).
ADS Google Scholar
Lei, C. et al. Impact of temperature and geothermal gradient on sandstone reservoir quality: The Baiyun Sag in the Pearl River Mouth Basin study case (northern South China Sea). Minerals 8, 452 (2018).
Article ADS CAS Google Scholar
Pang, X. et al. Basic geology of Baiyun deep-water area in the northern South China Sea. China Offshore Oil Gas 20, 215–222 (2008) ([in Chinese with English abstract]).
Google Scholar
Liu, B. et al. Middle Permian environmental changes and shale oil potential evidenced by high-resolution organic petrology, geochemistry and mineral composition of the sediments in the Santanghu Basin, Northwest China. Int. J. Coal Geol. 185, 119–137 (2018).
Article CAS Google Scholar
Hillier, S. Quantitative analysis of clay and other minerals in sandstones by x-ray powder diffraction (XRPD). In Clay mineral cements in sandstones (Worden, R. H. & Morad, S. eds.) International Association of Sedimentologists Special Publication. 34, 213–251 (2003).
Coplen, T. B., Kendall, C. & Hopple, J. Comparison of stable isotope reference samples. Nature 302, 236–238 (1983).
Article ADS CAS Google Scholar
Folk, R. L., Andrews, P. B. & Lewis, D. Detrital sedimentary rock classification and nomenclature for use in New Zealand. N. Z. J. Geol. Geophys. 13, 937–968 (1970).
Article Google Scholar
Irwin, H., Curtis, C. & Coleman, M. Isotopic evidence for source of diagenetic carbonates formed during burial of organic-rich sediments. Nature 269, 209–213 (1977).
Article ADS CAS Google Scholar
Shi, X. B., Qiu, X. L., Xia, K. Y. & Zhou, D. Characteristics of surface heat flow in the South China Sea. J. Asian Earth Sci. 22, 265–277 (2003).
Article ADS Google Scholar
Song, Y. et al. Tectono-thermal modeling for Qiongd ongnan Basin and Pearl River Mouth Basin in the northern South China Sea. Chin. J. Geophys. 54, 3057–3069 (2011) ([in Chinese with English abstract]).
Article Google Scholar
Yuan, Y. et al. Uniform geothermal gradient’ and heat flow in the Qiongdongnan and Pearl River Mouth Basins of the South China Sea. Mar. Pet. Geol. 26, 1152–1162 (2009).
Article Google Scholar
Li, C. et al. Impact of high thermal setting and fluid activities on sandstone compaction: A case study of the Baiyun Sag in the Pearl River Mouth Basin (Northern South China Sea). Geofluids 8, 1–15 (2021).
Google Scholar
Chen, H. H., Chen, C. M., Pang, X., Jiahao, W. H. & Shi, W. Z. Natural gas sources, migration and accumulation in the shallow water area of the Panyu lower uplift: An insight into the deep water prospects of the pearl river mouth basin, South China Sea. J. Geochem. Explor. 89, 47–52 (2006).
Article CAS Google Scholar
Rozanski, K., Araguas-Araguas, L. & Gonfiantini, R. Isotopic patterns in modern global precipitation. Geophys. Monogr. 78, 1–36 (1992).
ADS Google Scholar
Kim, T. & O’Neil, J. R. Equilibrium and non-Equilibrium oxygen isotope effects in synthetic carbonates. Geochim. Cosmochim. Acta 61, 3461–3475 (1997).
Article ADS CAS Google Scholar
Schmidt, M., Xeflide, S., Botz, R. & Mann, S. Oxygen isotope fractionation during synthesis of Ca Mg-carbonate and implications for sedimentary dolomite formation. Geochim. Cosmochim. Acta 69, 4665–4674 (2005).
Article ADS CAS Google Scholar
Giles, M. R. & de Boer, R. B. Origin and significance of redistributional secondary porosity. Mar. Pet. Geol. 7, 378–397 (1990).
Article Google Scholar
Wang, Y. Z. et al. Sources of authigenic quartz in the Permian tight sandstones close to Gaoqing Fault, Dongying Sag, Bohai Bay Basin. China. Mar. Pet. Geol. 113, 104109 (2020).
Article CAS Google Scholar
Hyodo, A., Kozdon, R., Pollington, A. D. & Valley, J. W. Evolution of quartz cementation and burial history of the Eau Claire Formation based on in situ oxygen isotope analysis of quartz overgrowths. Chem. Geol. 384, 168–180 (2014).
Article ADS CAS Google Scholar
dos Anjos, S. M., De Ros, L. F., de Souza, R. S., de Assis Silva, C. M. & Sombra, C. L. Depositional and diagenetic controls on the reservoir quality of Lower Cretaceous Pendencia sandstones, Potiguar rift basin. Braz. AAPG Bull. 84, 1719–1742 (2000).
Horita, J. Oxygen and carbon isotope fractionation in the system dolomite-water-CO2 to elevated temperatures. Geochim. Cosmochim. Acta 129, 111–124 (2014).
Article ADS CAS Google Scholar
Mi, L. J. et al. Integrated study on hydrocarbon types and accumulation periods of Baiyun sag, deepwater area of pearl river mouth basin under the high heat flow background. China Offshore Oil Gas 31, 1–12 (2019) ([in Chinese with English abstract]).
Google Scholar
Liu, B. et al. Impact of thermal maturity on the diagenesis and porosity of lacustrine oil-prone shales: Insights from natural shale samples with thermal maturation in the oil generation window. Int. J. Coal Geol. 261, 1–14 (2022).
Article Google Scholar
Zhang, G. C. et al. The Baiyun Sag: A giant rich gas-generation sag in the deepwater area of the Pearl River Mouth Basin. Nat. Gas Ind. 34, 11–25 (2014) ([in Chinese with English abstract]).
Google Scholar
Curtis, C. D. Possible links between sandstone diagenesis and depth-related geochemical reactions occurring in enclosing mudstones. J. Geol. Soc. 135, 107–117 (1978).
Article ADS CAS Google Scholar
Zhu, J. Z. et al. Origins and geochemical characteristics of gases in well LW3-1-1 in the deep sea region of Baiyun Sag, Pearl River Mouth Basin. Nat. Gas Geosci. 19, 229–233 (2008) ([in Chinese with English abstract]).
CAS Google Scholar
Zhu, W. L. et al. Geochemistry, origin, and deep-water exploration potential of natural gases in the Pearl River Mouth and Qiongdongnan basins, South China Sea. AAPG Bull. 93, 741–761 (2009).
Article CAS Google Scholar
Whiticar, M. J., Faber, E. & Schoell, M. Biogenic methane formation in marine and freshwater environments: CO2 reduction vs. acetate fermentation-Isotope evidence. Geochim. Cosmochim. Acta 50, 693–709 (1986).
Dutton, S. P. Calcite cement in Permian deep-water sandstones, Delaware Basin, west Texas: Origin, distribution, and effect on reservoir properties. AAPG Bull. 92, 765–787 (2008).
Article CAS Google Scholar
Chuhan, F. A., Bjorlykke, K. & Lowrey, C. J. Closed system burial diagenesis in reservoir sandstones examples from the Garn Formation at Haltenbanken area, Offshore Mid-Norway. J. Sediment. Res. 71, 15–26 (2001).
Article ADS CAS Google Scholar
Bjørlykke, K. Relationships between depositional environments, burial history and rock properties. Some principal aspects of diagenetic process in sedimentary basins. Sediment. Geol. 301, 1–14 (2014).
Surdam, R. C., Crossey, L. J., Hagen, E. S. & Heasler, H. P. Organic-inorganic interactions and sandstone diagenesis. AAPG Bull. 73, 1–23 (1989).
CAS Google Scholar
Thyne, G. A model for diagenetic mass transfer between adjacent sandstone and shale. Mar. Pet. Geol. 18, 743–755 (2001).
Article CAS Google Scholar
Liu, Y. F. et al. Fluid-rock interaction and its effects on the Upper Triassic tight sandstones in the Sichuan Basin, China: Insights from petrographic and geochemical study of carbonate cements. Sediment. Geol. 383, 121–135 (2019).
Article ADS CAS Google Scholar
Boles, J. R. & Franks, S. G. Clay diagenesis in Wilcox sandstones of southwest Texas: Implications of smectite diagenesis on sandstone cementation. J. Sediment. Res. 49, 5–70 (1979).
Google Scholar
Wang, J. et al. Pore fluid evolution, distribution and water-rock interactions of carbonate cements in red-bed sandstone reservoirs in the Dongying Depression. China. Mar. Pet. Geol. 72, 279–294 (2016).
Article CAS Google Scholar
Azmy, K. & Blamey, N. J. F. Source of diagenetic fluids from fluid-inclusion gas ratios. Chem. Geol. 347, 246–254 (2013).
Article ADS CAS Google Scholar
Wang, D. F., Luo, J, L., Chen, S. H., Hu, H. Y., Ma, Y. K., Li, C., Liu, B. J. & Chen, L. Carbonate cementation and origin analysis of deep sandstone reservoirs in the Baiyun sag, Pearl River Mouth Basin. Acta Geol. Sin. 91, 2079–2090 (2017), [in Chinese with English abstract].
Taylor, T. R. et al. Sandstone diagenesis and reservoir quality prediction: Models, myths, and reality. AAPG Bull. 94, 1093–1132 (2010).
Article Google Scholar
Wilkinson, M. & Haszeldine, R. S. Oil charge preserves exceptional porosity in deeply buried, overpressured, sandstones: Central North Sea. UK. J. Geol. Soc. 168, 1285–1295 (2011).
Article ADS CAS Google Scholar
Luo, X. R. et al. Oil accumulation process in the low-permeability Chang-81 member of Longdong area, the Ordos Basin. Oil Gas Geol. 31, 770–778 (2010) ([in Chinese with English abstract]).
Google Scholar
Fassi-Fihri, O., Robin, M. & Rosenburg, E. Wettability studies at the pore level: A new approach by use of cryo-scanning electron microscopy. SPE Form. Eval. 10, 11–19 (1995).
Article Google Scholar
Download references
This research work was funded by the National Natural Science Fund, China (Grant No. 42262020), Major Projects of National Science and Technology, China (Grant No. 2016ZX05026) and the Research Program of Science and Technology at Universities of Inner Mongolia Autonomous Region (Grant No. NJZY22445). CNOOC Research Institute Company Limited are gratefully acknowledged for providing the data and analytical report.
Institute of Mining and Coal, Inner Mongolia University of Science and Technology, Baotou, 014010, China
Bing Tian, Yihan Yuan, Youwei Zheng, Ming Liu & Cheng Guo
Institute of Science, Inner Mongolia University of Science and Technology, Baotou, 014010, China
Jun Tang & Shanshan Zuo
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
B.T., Y.Y. and J.T. designed the research; S.Z. improved the revised version; Y.Z. reviewed the methodology and results; and M.L. and C.G. designed the figures. All authors reviewed the manuscript.
Correspondence to Bing Tian.
The authors declare no competing interests.
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
Reprints and Permissions
Tian, B., Yuan, Y., Tang, J. et al. Fluid evolution and related fluid–rock interactions of the Oligocene Zhuhai sandstones in the Baiyun Sag, northern margin of the South China Sea. Sci Rep 13, 14067 (2023). https://doi.org/10.1038/s41598-023-41428-3
Download citation
Received: 05 May 2023
Accepted: 26 August 2023
Published: 28 August 2023
DOI: https://doi.org/10.1038/s41598-023-41428-3
Anyone you share the following link with will be able to read this content:
Sorry, a shareable link is not currently available for this article.
Provided by the Springer Nature SharedIt content-sharing initiative
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.